Aem Infinity Supported Applications - Universal V8 Eng Manuale Utente Scaricare il pdf (Pagina 41)

Universal 8

41

© 2014 AEM Performance Electronics

Infinity

Pin

Hardware Ref.

7100-XXXX-62

7101-XXXX-63

Function

Hardware Specification

Notes

C1-61

+12V

+12V In

12 v olt power f rom relay

12 v olt power f rom relay . Relay must be

controlled by +12V Relay Control signal,

pin C1-29 abov e.

C1-62

Injector 2

Injector 2

Saturated or peak and hold, 3A max

continuous

Injector 2

C1-63

Injector 1

Injector 1

Saturated or peak and hold, 3A max

continuous

Injector 1

C1-64

+12V

+12V In

12 v olt power f rom relay

12 v olt power f rom relay . Relay must be

controlled by +12V Relay Control signal

pin C1-29 abov e.

C1-65

+12V_SW

Ignition Switch

10K pulldown

Full time battery power must be av ailable

at C1-10 bef ore this input is triggered.

C1-66

Analog_In_Temp_1

Coolant Temp

Sensor

12 bit A/D, 2.49K pullup to 5V

See "Coolant Temperature" Setup Wizard

f or selection.

C1-67

Analog_In_Temp_2

Intake Air

Temperature

12 bit A/D, 2.49K pullup to 5V

See "Air Temperature" Setup Wizard f or

selection.

C1-68

Analog_In_Temp_3*

Spare Temp

Input

12 bit A/D, 2.49K pullup to 5V

Normally used f or Oil Temp input. *Pin

not populated in 30-3805 Univ ersal V8

Base harness.

C1-69

Stepper_2A

Stepper 2A

Automotiv e, Programmable Stepper

Driv er, up to 28V and ±1.4A

Be sure that each internal coil of the

stepper motor are properly paired with the

1A/1B and 2A/2B ECU outputs. Supports

Bi-Polar stepper motors only .

C1-70

Stepper_1A

Stepper 1A

Automotiv e, Programmable Stepper

Driv er, up to 28V and ±1.4A

Be sure that each internal coil of the

stepper motor are properly paired with the

1A/1B and 2A/2B ECU outputs. Supports

Bi-Polar stepper motors only .

C1-71

Stepper_2B

Stepper 2B

Automotiv e, Programmable Stepper

Driv er, up to 28V and ±1.4A

Be sure that each internal coil of the

stepper motor are properly paired with the

1A/1B and 2A/2B ECU outputs. Supports

Bi-Polar stepper motors only .

C1-72

Stepper_1B

Stepper 1B

Automotiv e, Programmable Stepper

Driv er, up to 28V and ±1.4A

Be sure that each internal coil of the

stepper motor are properly paired with the

1A/1B and 2A/2B ECU outputs. Supports

Bi-Polar stepper motors only .

C1-73

Power Ground

Ground

Power Ground

Connect directly to battery ground

C2-1

DBW2 Motor +*

DBW Motor

Control Open

5.0A max Throttle Control Hbridge Driv e

+12V to open. *Pin not populated in 30-

3805 Univ ersal V8 Base harness.

C2-2

DBW2 Motor -*

DBW Motor

Control Close

5.0A max Throttle Control Hbridge Driv e

+12V to close. *Pin not populated in 30-

3805 Univ ersal V8 Base harness.

C2-3

Power Ground

Ground

Power Ground

Connect directly to battery ground

C2-4

Injector 7

Injector 7

Saturated or peak and hold, 3A max

continuous

Injector 7

C2-5

Injector 8

Injector 8

Saturated or peak and hold, 3A max

continuous

Injector 8

C2-6

Injector 9*

Injector 9

Saturated or peak and hold, 3A max

continuous

Injector 9. *Pin not populated in 30-3805

Univ ersal V8 Base harness.

C2-7

Injector 10*

Injector 10

Saturated or peak and hold, 3A max

continuous

Injector 10. *Pin not populated in 30-3805

Univ ersal V8 Base harness.

1 2 ... 36 37 38 39 40 41 42 43 44 45 46

Commenti su questo manuale

Nessun commento